Rane Elastomer Processors


EnglishFrenchGermanItalianPortugueseSpanish


Rubber Sleevings


Rubber Sleevings

We are looked upon as one of the staggering Rubber Sleevings Manufacturers & Exporters from India. The unmatched quality and unsurpassable performance have made our Rubber Sleevings widely demanded in various industrial sectors.

Material Used :
  • Silicone Rubber
  • Neopreneo Nitrile PVC
  • Viton

Advantages :
  • Good Mechanical Properties
  • Resistance to abrasion & solvents
  • Moderate resistance to oil
  • Good resistance to oil
  • Good resistance to weathering
  • Excellent ozone resistance
  • Self extinguishing

Grades :
  • Electrical Grade
  • Medical Grade
  • Food Processing Grade

Silicone Sleevings for Electrical Insulation

Ranelast Silicone Sleeving Has Inherent Dielectric Strength Allied with Resistance to High
temperatures, High Voltage Ionisation, Arcing, Ultra Violet Light and Ozone Plus Carona Resistance Comparable with that of Mica, Make It Dependable in the Most Rigorous Electrical Applications Including Moisture Laden Conditions. It Will Continue to Insulate Even in Severe Vibratory
Conditions,After Reduction to Silicone Dioxide Ash By Direct and Rubber Flame Contact.

The Silicone Sleevings are Manufactured in Transparent or Opaque Versions. They Areavailable in Any Diameter and Wall Thickness, Any Length &any Colour.

Manufacturing Sleevings as Small as 0.20 Mm Wall Thickness is Rane's Forte. 0.20 Mm Wall Thickness is Rane's Forte. Procedure Right from the Stage of Raw Material, Formulation, Compounding & Mixing to Extruding Finishing and Physical Measurement. They are Rigorously Tested to the Most Punishing Requirements Subject to Ardorous Duties as per Standard B. S 2848 Type 5 & B. S G.i 98 Type 4 When Carefully Compounded and Extruded, It Gives Following Excellent Properties.

a)Resistance to Steam Ageing, Power
factor,Permittvity,Electrolytic Corrossion. Smooth, Free from Bubbles, Pinholes and Creases in Appearance. Low Space Factor, Long Life, No Cracking After Bending, Withstand 48 Hours At 180' C Without Cracking Withstand Low Temp upto -s5'c Without Cracking and Elongation 240% to 280% Observed for 1.00 Mm Dia & 330% to 360% for 12 Mm Diarate of Burning Satisfactory. Volatile Content-satisfactory.

b)Mould Groth : No Mould Growth Visible to Eyesight.
c)Voltage Proofing : At Room Temp, in Air for 1 Mm Di~ with Stand 7 Kv Rms for 1 Minute (at 180' C 1mm Dia Withstands 4.9 Kv Rms for 1 Minute) At Room Temp. in Air for 12mm Dia Withstands 10 Kv Rms for 1 Minute (at 180·c for 12mm Dia Withstands 7 Kv Rms for 1 Minute)
d)Insulation Resistance : Electrical Insulation 500 Volts are Insulated By a Thickness of 1mill. At Room Temperature. 1mm Dia Sleeving : 50 X 10' to 200 X10' Megaohms, 12mm Dia 5x10' to 50x 10' Megaohms.

After Accelerated Damp Heat Treatment:1mm Dia 5 X 10' to 50 X 10' Megaohms.12mm Dia 2 X 10' to 5 X 10' Megaohms.

5/64" Insulation On 20, Gauge Wire Hot Air Vulcanised Insulation Resistance: 20,000 Ohms per 1000 Feet, After 24 Hours Immersion 10,000 Ohms per 1000 Feet, Electric Strength: 18 Kvac.